Undercuts door jambs and other wall base obstacles. Eliminates intricate fitting work. Specially shaped 12" long blade permits right or left hand cutting. The comfortable wood handle is sufficiently offset to provide knuckle protection. Supplied with a small knob for optional use (in place of the front wing nut) for …

This tool removes door pins fast and easy without causing damage. The forked end fits snugly around the head of the pin so that equal pressure is applied to both sides.

Scrape faster and work less with a razor sharp 8" blade. Length is adjustable from 39” to 59” for maximum comfort whether kneeling or standing. Adjustment is quick and easy. Each scraper has a comfortable vinyl grip and four case hardened screws to resist slot wear and give maximum …

Scrape faster and work less with a razor sharp 8" blade. Length is adjustable from 19” to 29” for maximum comfort and efficiency. Adjustment is quick and easy. Each scraper has a comfortable vinyl grip and four case hardened screws to resist slot wear and give maximum blade holding …

Features a blade stabilizer that minimizes deflection for better cutting, and 1-13/16" long blades for diagonal cuts in regular strip or straight cuts in architectural strip. The handle locks in three positions: closed; partially open for cutting 9/32" strip and full open for cutting thicker strip. Extra blades can be …

For use with the No. 450 Tackless Strip Cutter. Sold 12 blades per package.

Gives a tighter and more uniform installation—with less effort and without sore knees. Designed for waterfall type installations, stretching is done from the top of a stairway down. Stairs are easier to install because gravity is working with you—not against you. To use, stretch runner, then use a stair tool …

This adjustable height stapling tool works as close as one board width of walls to reduce gluing, or top nailing and puttying. The height adjusts for boards from 3/8" to 3/4" thick. Can drive both 18 gauge 1/4" crown staples, or L-shaped (only) cleats, and has a built-in staple separator …

This 36-tooth, 5-5/8" diameter Carbide Tipped Steel Blade is bell shaped for flush cutting wood and added rigidity. For use with the No. 575 Multi-Undercut Saw as well as retired saw models Nos. 545 and 555. Caution: As these blades are subject to possible abuse, they are not guaranteed. …

This tool gives positive leverage control to avoid denting the baseboard. It is also specially designed to lift the moulding at approximately the same angle that the nails were driven. The smoothly ground slim ends enter easily under the mouldings, and both are notched for nail and brad pulling. The …

This saw undercuts walls, door jambs, toe spaces and will also fully undercut inside corners up to 1/4" deep. The height of cut is easily adjustable from flush to 1" above the floor in 3/32" increments. The large flat base helps prevent tipping and assures accurate, level cutting. Has …

The Opto Power Tacker has a ruggedized electronic control board including an optical sensor that fires in response to the motion of a tough sliding trigger. The delicate mechanical microswitch of previous tackers, which frequently required repair, has been eliminated. This tacker also has a long, slender nose that more …

This knife holds the blade at the proper angle to allow easy cutting of carpet pad. Made from die cast aluminum and has a quick opening D-ring fastener. Has blade storage space in the handle. Slotted razor blades are not supplied.

The extended spindle, low-profile cutting head, and flush-mounted blade of this saw allow it to cut all the way against the inner wall of a toe-kick for removing old underlayment. The hinged depth adjustment plate has five settings for common underlayment thicknesses including 1/4", 3/8", 1/2", 5/8", or 3/4". Also …

This Carbide Tipped blade has 18 teeth and is 3-3/8" in diameter. Depth of cut is 3/4". This blade is compatible with all versions of the Crain Toe-Kick Saw. Caution: As these blades are subject to possible abuse, they are not guaranteed. Blades are not recommended …